Scheme-it

This project is a wireless power transmission system that works on the principle of magnetic induction. This wireless charging system works as the digital switched mode power supply with the transformer, which is separated into two parts: The transformer primary coil works as the transmitter coil, and the transformer secondary coil serves as the receiver. This system works based on magnetic induction, the better coupling between the transmitter coil and receiver coil gain, the better system efficiency. So the receiver coil should be closely and center-aligned with the transmitter coil as possible. After the receiver coil receives the power from the transmitter coil by magnetic field, it regulates the received voltage to power the load, and send its operational information to transmitter according to specific protocol by the communication link. Then the system can achieve the closed-loop control, and power the load stably and wirelessly.

This circuit design allows full evaluation capability of the PF0100 SMARTMOS Power Management Integrated Circuit (PMIC) for the i.MX6 family of application processors. The PF0100 provides a highly programmable/ configurable architecture, with fully integrated power devices and minimal external components. With on-chip One Time Programmable (OTP) memory, the PF0100 is available in preprogrammed standard versions, or non-programmed to support custom programming. The PF0100 is defined to power an entire embedded MCU platform solution such as i.MX6 based eReader, IPTV, medical monitoring, and home/factory automation.

The MAX32630FTHR Pegasus board is a rapid development platform designed to help engineers quickly implement battery optimized solutions with the MAX32630 ARM® Cortex® -M4F microcontroller. The board also includes the MAX14690 wearable PMIC to provide optimal power conversion and battery management.
-MAX32630 Microcontroller

Features:

ARM Cortex-M4F, 96MHz-2048KB Flash Memory

512KB SRAM

8KB Instruction Cache

Full-Speed USB 2.0

Three SPI Masters, One Slave

Three I2C Masters, One Slave

Four UARTS

1-Wire Master

66 GPIO

4 Input 10-Bit ADC

-MAX14690 Wearable PMIC

Battery Charger with Smart Selector

Dual Micro IQ Buck Regulators

Three Micro IQ Linear Regulators

Power-On/Off Sequencing Controller

Voltage Monitor Multiplexer

-Expansion Connections

Breadboard-Compatible Headers

Micro SD Card Connector

Battery Connector

Micro USB Connector

-Integrated Peripherals

RGB Indicator LED

6-Axis Accelerometer/Gyro

Dual-Mode Bluetooth Module

User Pushbutton

-mbed® HDK Debug Interface

Drag-and-Drop Programming

SWD Debugger

Virtual UART Console

The Raspberry Pi 3 is the third generation Raspberry Pi model. It replaces the Raspberry Pi 2 Model B. Compared to the Raspberry Pi 2 it has the following upgrades:

• A 1.2GHz 64-bit quad-core ARMv8 CPU
• 802.11n Wireless LAN
• Bluetooth 4.1
• Bluetooth Low Energy (BLE)
• 1GB RAM
• 4 USB ports
• 40 GPIO pins
• Full HDMI port
• Ethernet port
• Combined 3.5mm audio jack and composite video
• Camera interface (CSI)
• Display interface (DSI)
• Micro SD card slot (now push-pull rather than push-push)
• VideoCore IV 3D graphics core

The DE0-Nano-SoC board is a hardware design platform based on the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility. It has many features that allow users to implement a wide range of designed circuits, from simple circuits to various multimedia projects.

FPGA Device

-Altera Cyclone® V SE 5CSEMA4U23C6N device

-Serial configuration device

-USB-Blaster II onboard for programming; JTAG mode

-2 push-buttons

-4 slide-switches

-8 green user LEDs

-Three 50MHz clock sources from the clock generator

-Two 40-pin expansion header

-One Arduino expansion header (Uno R3 compatibility), can connection with Arduino shields.

-One 10-pin analog input expansion header (shared with Arduino analog input).

-A/D converter, 4-pin SPI interface with FPGA

HPS (Hard Processor System)

-925MHz Dual-core ARM Cortex-A9 processor

-1GB DDR3 SDRAM (32-bit data bus)

-1 Gigabit Ethernet PHY with RJ45 connector

-USB OTG port, USB micro-AB connector

-Micro SD card socket

-Accelerometer (I2C interface plus interrupt)

-UART to USB, USB mini-B connector

-Warm-reset button and cold-reset button

-One user button and one user LED

-LTC 2 x 7 expansion header

The MAX 10 Evaluation Kit is an entry-level board for evaluating the MAX 10 FPGA technology and Enpirion PowerSoC regulators. This evaluation board features the following:

• MAX 10 FPGA (10M08, single power supply, 144-pin EQFP)

• Enpirion EP5388QI point-of-load PowerSoC, 800 mA, DC-DC step-down (buck) converter with an integrated inductor

• JTAG header for download cable programming (POF) or configuration (SOF)

• 50 MHz single-ended, external oscillator clock source

• Shunt resistors and probe points to measure FPGA power

• Switch, push buttons, jumpers, and status LEDs

This evaluation board also contains connectors such as the following:

• Arduino headers to accept UNO R3 compatible Shields

• General-purpose through-hole vias

• Type mini-B USB connector (power source)

• USB cable included

• Footprint to install a potentiometer (customer must purchase and install)

The PSoC Analog Coprocessor Pioneer Kit offers footprint-compatibility with Arduino™ shields and baseboards. This kit features five onboard sensors, an RGB LED, two push-button switches, an onboard programmer/debugger and USB-UART/I2C bridge functionality block (KitProg2), and a Cypress F-RAM™. This kit supports operating voltages of 1.8 V, 3.0 V (coin cell operated), 3.3 V or 5 V.

The Kit is intended for use with PSoC Creator™ to develop and debug your PSoC Analog Coprocessor device projects. PSoC Creator is Cypress' standard integrated design environment (IDE). If you are new to PSoC Creator, see the documentation on the PSoC Creator home page. You can also refer the application note, AN211293 – Getting Started with PSoC Analog Coprocessor, which gives an introduction to the PSoC Analog Coprocessor device.

For More information http://www.digikey.com/en/product-highlight/c/cypress/psoc-analog-coprocessor-with-te-sensor

The TM4C123G LaunchPad Evaluation Kit is a low-cost evaluation platform for ARM Cortex-M4F based microcontrollers from Texas Instruments. The EK-TM4C123GXL also features programmable user buttons and an RGB LED for custom applications. The stackable headers of the TM4C123G LaunchPad BoosterPack XL Interface make it easy and simple to expand the functionality of the TM4C123G LaunchPad when interfacing to other peripherals with Texas Instruments MCU BoosterPack. The design of the TM4C123G LaunchPad highlights the TM4C123GH6PM microcontroller with a USB 2.0 device interface and hibernation module.

The ARM Cortex-M4F Based MCU TM4C123G LaunchPad Evaluation Kit (EK-TM4C123GXL) offers these features:

• Tiva TM4C123GH6PMI microcontroller

• Motion control PWM

• USB micro-A and micro-B connector for USB device, host, and on-the-go (OTG) connectivity

• RGB user LED

• Two user switches (application/wake)

• Available I/O brought out to headers on a 0.1-in (2.54-mm) grid

• On-board ICDI

• Switch-selectable power sources: – ICDI – USB device

• Reset switch

• Preloaded RGB quickstart application

• Supported by TivaWare for C Series software including the USB library and the peripheral driver library

• Tiva C Series TM4C123G LaunchPad BoosterPack XL Interface, which features stackable headers to expand the capabilities of the Tiva C Series LaunchPad development platform

Circuit Playground is an all-in-one board that has sensors and LEDs built in.

• ATmega32u4 Processor, running at 3.3V and 8MHz
• MicroUSB port for programming and debugging with Arduino IDE
• USB port can act like serial port, keyboard, mouse, joystick or MIDI
• 10 x mini NeoPixels, each one can display any color
• 1 x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection)
• 1 x Temperature sensor (thermistor)
• 1 x Light sensor (phototransistor)
• 1 x Sound sensor (MEMS microphone)
• 1 x Mini speaker (magnetic buzzer)
• 2 x Push buttons, left and right
• 1 x Slide switch
• 8 x alligator-clip friendly input/output pins
• Includes I2C, UART, and 4 pins that can do analog inputs/PWM output
• All 8 pads can act as capacitive touch inputs
• Green "ON" LED so you know its powered
• Red "#13" LED for basic blinking
• Reset button

CC3200 SimpleLink™ Wi-Fi® and IoT Solution with MCU LaunchPad Hardware.

The high performance CC3200 is the industry's first single-chip Microcontroller (MCU) with built-in Wi-Fi connectivity for the LaunchPad™ ecosystem. Created for the Internet of Things (IoT), the SimpleLink WiFi CC3200 device is a wireless MCU that integrates a high-performance ARM® Cortex®-M4 MCU allowing customers to develop an entire application with a single IC. With on-chip Wi-Fi, internet and robust security protocols, no prior Wi-Fi experience is needed for faster development.